Sidewinder-X1 and Genius firmware flashing guide

                Artillery Sidewinder-X1 and Genius

                            firmware flashing guide

Written by Gavin Balcomb


So, the time has come for you to upgrade the firmware on your printer, at first, this may seem like a daunting task, however, this guide will take you step by step through the process.

There are a few things you need to know before we dive right into it.

When flashing any mainboard with firmware, there is always some level of risk involved, so proceed at your own risk. We will also need to remove the bottom cover, voiding your warranty. We need to be able to unplug the TFT board (the screen) in order to free up a communications port on your motherboard. Lastly, you need to understand that the firmware you put on your board controls how your machine behaves, for better… or worse…


This guide assumes that you have already opened the bottom panel and disconnected the TFT.

Now that we got that out of the way, let's begin. 

Downloading and extracting the firmware

The first part of the process is to get some firmware to flash, I would recommend sticking to the firmware provided by artillery or the precompiled firmware available from the downloads section of the forum.

(for advanced users, if you wish to start with a fresh build of marlin you can download their latest release branch from https://marlinfw.org/meta/download/

1.  in your browser, navigate to http://www.artillery3d.com/


2.  On the Artillery website, navigate to “Support” and click on “Downloads

3.  Click on “Sidewinder or Genius Firmware” for your respective printer.


4.  Click the button to download the file. 

Please note, you are also able to download the firmware for the TFT from this same location.

Now we need to extract the downloaded files

1.       Open up file explorer (finder if on mac) and navigate to your downloads folder and find the files we downloaded previously, please note they will be compressed files with the extensions “.rar” or “.zip”

2.       Cut or copy the files to a location or folder where you will be able to find them easily.


3.       If the file has the extension “.rar”, change the extension to “.zip”


4.       We can now extract the Zip file to be able to explore and use the content, right-click the “.zip” file and select “Extract to”. 


Downloading and installing Arduino IDE


In your browser, type the below into your address bar, or enter the Arduino site and navigate to software/downloads.

1.       You can download Arduino IDE from the link below, alternatively type the following into your URL bar



2.       Select and download the correct build for your operating system

You will then be prompted with a screen where you can choose to donate to development or just download, the choice is yours.


3.       Once the software is download, navigate to your downloads folder, right-click on the .exe and run as “administrator”


4.       Select Yes to the prompt to allow changes to the computer 

5.       Proceed through the installer and press the install button


6.       Once the program is installed, navigate to where you kept the firmware downloaded previously and open the folder.



Double click on the folder called “Marlin”, scroll through the content until you find the file “Marlin.ino” Double click this to open the file. This will open Arduino IDE with the files in it ready to go.


Arduino IDE


When the IDE Opens after following the steps above you will be presented with the following screen. With a bunch of different tabs open.


The two tabs that we are interested in though are the “Configuration.h” and “Configuration_adv.h” files


These two tabs contain all the settings that we can configure to turn on/off features in the marlin software, such as;

1.       EEPROM – in Config.h


2.       Linear Advance – in Config_adv.h


3.       Mesh levelling and Auto Bed Leveling – in Config.h

4.       BLTouch – in Config.h

And many, many more. If you wish to find a setting press “CRTL + F” on your keyboard and search for it, note the default search will only search within the tab you have open.


Compiling and Uploading your firmware

Once you have made all the changes that you wanted to make, we now need to compile the firmware to make sure it works, and if that succeeds we need to upload it to the mainboard

1.       When you are happy with your changes we will press the verify button in Arduino to see if it will successfully build, this is the button in the top left-hand corner, this will begin the build and check for any errors.


2.       If that completes successfully we can now plug our printer into the computer  

3.       Once the printer is connected to the computer we need to go into the “tools” menu and change the board to “Arduino Mega or Mega 2560”


4.       Next, we will set the Com Port to connect over, please note COM1 is usually system reserved and unlikely to be the correct port.


5.       Lastly, we will press “Get Board Info” and it should return something similar to below


6.       We can now press the “Upload” button to begin uploading our software


7.   The status of the upload will show up in the terminal window at the bottom with the results of the upload. The below is what you would expect to see if the upload is successful


CONGRATULATIONS! You just flashed the firmware on your printer, now you just need to reassemble everything and flash the TFT if you are doing that as well and you are good to go! (please remember you will need to redo/reset any calibrations you had set in the EEPROM, such as ESTEPS, or linear advance etc…) 


As with anything, sometimes things don’t go according to plan, below is a screenshot of an error during the upload, in this case, the machine was unable to communicate with the printer over the selected COM port, this was due to having Cura4.5 open which was using that port. To resolve the issue, I closed Cura4.5 and attempted the upload again. Keep in mind that if there are any errors with your build or your configuration, they will show up in this window which will tell you what you need to go back and change.



1reply Oldest first
  • Oldest first
  • Newest first
  • Active threads
  • Popular
Like1 Follow
  • 1 mth agoLast active
  • 1Replies
  • 653Views
  • 3 Following